Break's

Text

Exact  

Finnish Bit Wizards - Stripper v1.1DetailsCaseRow
Info
INSTRUCTIONS FOR STRIPPER AND RIPPERDOS ! READ THEM BEFORE USE !

----------------------------------------------------------------------
  Stripper   -   Reset-activated SoundTracker-tune ripper

  RipperDOS   -   File convert program for Stripper

  Stripper and RipperDOS are both coded by TOTO of FINNISH BIT WIZARDS
  Stripper's playroutine is coded by TIP of The New Masters.
----------------------------------------------------------------------

Stripper:

   When Stripper is loaded, it prompts following text to cli-window:

      Stripper V1.1 - installed
      (reset to activate)

   If not, then something is very badly wrong. After that message,
   Stripper is activated by pressing CTRL-CBM-AMIGA -keys.Stripper
   functions are selected by moving mouse up and down and pressing
   left and rightmousebuttons. These are the functions:

   Search Tune:
      Left button searches the next possible soundtracker module.
      Searching is automatically stopped when it reaches the end
      of the CHIP-memory. If left button is pressed after that,
      search begins again from the beginning of the memory.
      Right button resets the search counter, so that search can
      be started again in any time.

   Play Tune:
      When possible tune is found, it can be played out by selecting
      Play Tune - function and pressing left mousebutton. Playing
      stops by pressing and releasing the button again.

   Save Module:
      If there is soundtracker module found, it can be saved to
      disk by Save Module - function with left mousebutton.

   Save Song:
      Same as above, but it saves only the song, as the above saves
      the song and the instruments.

   Saving is done to the disk in the internal disk drive (unit 0). Disk
   must be RipperDOS-format disk. If it's not, or there is not enough
   space on that disk, nothing will be saved.

   ESC-Key switches filter on/off.

   Exiting the Stripper happens by resetting the Amiga again.



RipperDOS:

   When the RipperDOS-program is loaded (or after that, when disk is
   inserted to the drive), it searches the disk in unit 0. If disk is
   RipperDOS-format disk, program prints out it's directory. RipperDOS
   functions are as follows:

   Convert File:
      Converts the RipperDOS format file to the AmigaDOS file.

   Install to RipperDOS:
      Installs the formatted disk to the RipperDOS format.

   Quit:
      Exits the RipperDOS.

   File to be converted is selected by clicking left or right mousebutton
   above it's NAME-field.

   When Convert File - function is selected, it loads the selected file
   to the memory. After disk activity light goes off, remove the disk
   and insert AmigaDOS-disk. Then the file is automatically saved to it.
   Saving is done to the current directory, or if there is not specified
   current directory, to the root directory of the disk in unit 0.

   There's TIP's ST-PLAYROUTINE ON THIS DISK , you can use it to play
   ripped muzaks ! (It's source code , so use it from seka and load tune
  to place (BEGIN>-prompt) data !)

   IF YOU HAVE ANY QUESTIONS , PLEASE WRITE OR CALL TO :

   THE BLOT
   TOLKKILANKATU 10 A 12
   45150 KOUVOLA
   FINLAND
   TEL.  -358-51-10581 (IF YOU CALL FROM ABROAD)    ASK FOR MIKA !
             951-10581 (IF YOU CALL FROM FINLAND)

Disclaimer: Texts are presented here in their original form, control chars and all, with no edits or censorship. All texts have been already been voluntarely released to the public as a part of the demos. That said, if a text seen here contains information about you personally that you don't wish to be visible, contact me and I will remove it from the website.